My Account | Login | Checkout

You are not logged in

Enter the search term for the product you are looking for below:

More Options
Display my previous orders

To repeat a previous order in part or full, click the link above. To purchase or view any of the items you have purchased before, simply select it from the list below.



Click on image for full size
3 OHM 250 WATT POWER RESISTOR DIVERSION DUMMY LOAD 12V/24V
3 Ohm, 75 watts at 15 volts. (300 watts at 30 volts).

FVT250-3

Available in increments of 1
Quantity
Total Percent Off Per Unit
1
$12.50 0% $12.5000
2
$22.50 10% $11.2500
5
$50.00 20% $10.0000
$93.75 25% $9.3750
$181.25 27.5% $9.0625
$218.75 30% $8.7500
$406.25 35% $8.1250



Coleman Air

3 OHM - 500 WATT (total capacity) power resistor designed for 12 or 24 volt systems.

  • 75 watts at 15 volts -- see chart below.
  • 300 watts at 30 volts -- see chart below.

 

 

These resistors (heating elements) have been custom made specifically to perform as diversion (dummy) loads in solar/wind/hydro alternate energy systems.

Place multiple elements in parallel to increase the total wattage. See chart below.

Unlike water heating elements, these resistors do not need to be submerged in water or oil, they will dissipate the incoming energy in free air.


Each of the resistors we sell have been selected based on its ability to dissipate a very specific amount of power (watts) with a very specific resistance value (ohms), at a very specific voltage. When used as recommended, they will not burn out, even under continuous use.

Please note. These resistors will become hot during normal use, please mount them away from heat sensitive objects and out of the reach of children.


These custom heating elements are made with 20 gauge Kanthal A1 wire, wrapped around a ceramic tile, precision cut by our waterjet cutter (here in Coleman Texas) to yield 3 ohms.


500 Watt heating element

Image above may reflect wiring winding of other resistance values. Physical sizes of the tiles are standard.


Dimensions: Resistor body 6.9" long, approx. 1" square diameter, 5.80" terminals center to center, .19" diam terminal hole size. Terminals are made of .063-5052 aluminum.

 

 

Watts per single element at recommended voltages.


   Ohms   Volts   Amps   Watts
    
3.012.04.00 
48 
3.012.54.17 
52 
3.013.04.33 
56 
3.013.54.50 
61 
3.014.04.67 
65 
3.014.44.80 
69 
3.014.54.83 
70 
3.015.05.00 
75 

 

Area in green is where most diversion controllers would be set to divert.


This 3 ohm resistor will dissipate 5 amps at 15 volts. This is 75 watts. Since the resistor is rated at 250 watts in an enclosure, this is well within the safe operating range.


500 Watt heating element

Image above may reflect wiring winding of other resistance values. Physical sizes of the tiles are standard.



We have tested these elements at 400% design wattage and the resistors do not show any fatigue. The industrial rated, Kanthal A1 wire is extremely hardy, lasting 3 to 4 times longer than conventional elements using Nichrome wire. There is very limited oxidation of the wire even at very high temps and less than optimum humidity levels. Kanthal A1 wire is rated to 1400 degrees centigrade, more than 2000 degrees Fahrenheit.


Note: We do not recommend using the elements above 15 volts unless you enclose the resistors in firebrick or similar material as they will get VERY VERY hot within a matter of seconds, especially if you use multiple resistors side by side.The aluminum terminals will melt if this resistor is enclosed in a very small area and used at temperatures above 1000 F


We have set the recommended wattage of this resistor to 250 watts in an enclosure or 500 watts free air.

You may use the resistor up to 1500 watts without damage to the resistor providing you properly protect people and the surrounding area from the intense heat that is generated by even a single resistor at higher voltages. Using the resistor above these values must be done with extreme caution, as we have not tested them beyond the values stated above. The resistor itself is probably capable of handing much higher wattage; however, extreme caution must be taken to ensure your mounting and containment solution is capable of the heat being dissipated. DO NOT attempt to use this resistor above 60 volts, it, and possibly the surrounding area MAY BE DESTROYED!


If you double the voltage the resistor is used at, you quadruple the wattage! P=I^2*R (watts = the square of the amperage times the resistance.)

For a 3 ohm resistor:

12 volts (4 amps) = 48 watts (4 x 4 x 3)

24 volts (8 amps) = 192 watts (8 x 8 x 3)

30 volts (10 amps) = 300 watts (10 x 10 x 3)

48 volts (16 amps) = 768 watts (16 x 16 x 3) -- VERY HOT!


60 volts (20 amps) = 1200 watts (20 x 20 x 3) - -- -- VERY HOT!

75 volts (25 amps) = 1875 watts (25 x 25 x 3) - -- Resistor could be damaged, not recommended!


90 volts (30 amps) = 2700 watts (30 x30 x 3) - -- Resistor will be destroyed -- don't try it!





DO NOT USE IN OR AROUND WATER, THE KANTHAL WIRE IS NOT INSULATED AND WILL RESULT IN THE FULL VOLTAGE BEING TRANSFERRED TO THE WATER WHICH COULD BE LETHAL!!





Example of putting resistors in parallel (the image below depicts a different model resistor, however the hookup is the same.)

http://www.ccssoftware.com/ebay/images/10R100W_parallel.jpg

Place multiple resistors in parallel to increase the wattage/amperage.

  • 1 resistor at 15 volts = 75 watts.
  • 2 resistors in parallel at 15 volts = 150 watts.
  • 3 resistors in parallel at 15 volts = 225 watts.
  • 4 resistors in parallel at 15 volts = 300 watts. -- You get the picture.

 


 



Big things are happening from a lot of little companies, and if you notice the truly innovate products are being released from the new kids on the block.





Customers who bought this item also bought

40A Wind/Solar Charge Controller - Diversion Regulator
40 Amp 12/24 volts. Wind/Solar Diversion-Charge Load Controller
Completed Kit (No enclosure)

click to see more

170 Amp, 12V - 600V Blocking Diode Array with Enclosure
170 Amp, 12V - 600V Blocking Diode Array with Enclosure

click to see more

12V/24V DC Digital Red LED Panel Meter on/off Switch 30V Max No ext power needed

click to see more

440 A AMP 12v/24v/48v Solar/Wind/Hydro Regulator Diversion Controller HVM
Wind/Solar Diversion-Charge Load Controller.
440 Amp 12, 24 or 48 volts.
High contrast LED battery meter with on/off switch.
10,000 Watts! 8 x 12 Hoffman Box.
Reverse polarity protected.

click to see more

36 A Amp /48 V Volt 2160 Watt Diversion Dummy Load Resistor Radiant Air Heater
36A/48V 2160 Watt Diversion Dummy Load Resistor Heater
For 48 volt systems - Now with custom made, Kanthal-A1 wire wound resistors.

click to see more




Featured videos

Coleman Air Products

Copyright 2010-2017 Coleman Air, Inc. All rights reserved.

Have Questions? -- Please call us at 1-800-577-4169


We verify orders.

In addition to standard credit card verification procedures which insure the credit card is not stolen, we also verify the computer IP address, phone numbers, etc., to ensure the person placing the order is not doing so for fraudulent purposes. We work with all applicable agencies to prevent and/or report fraudulent or suspicious activity.

Official PayPal Seal